HUAWEI RTN 950 MANUAL PDF

OptiX RTN Radio Transmission System. VRC Commissioning and Configuration Guide (Web LCT). Issue, Date, HUAWEI. Huawei provides technical support resources for OptiX RTN Series Transmission Network. Access product manuals, HedEx documents, and visio stencils. Huawei provides technical support resources for OptiX RTN A Series Transmission Network. Access product manuals, HedEx documents, and visio stencils.

Author: Tojazilkree Tozilkree
Country: Uzbekistan
Language: English (Spanish)
Genre: Video
Published (Last): 10 November 2015
Pages: 408
PDF File Size: 17.42 Mb
ePub File Size: 7.94 Mb
ISBN: 764-1-59301-574-9
Downloads: 82609
Price: Free* [*Free Regsitration Required]
Uploader: Dijas

Step 4 Reset the performance event register. The topology clearly shows the structure of the network, the alarms of different NEs, subnets in the network, the communication status as well as the basic network operation status.

RTN VRC01 Commissioning Guide 04 – Huawei

It consists of an information payload the higher order VC and an AU pointer which indicates the offset of the payload frame start relative to the multiplex section frame start. Basic Installation Requirements The installation and maintenance personnel of Huawei devices must receive strict training and be familiar with the proper operation methods and safety precautions before any operation.

The New Maintenance Domain dialog box is displayed. The CPU has the ability to fetch, decode, and execute instructions and to transfer information to and from other resources over the computer’s main data-transfer huaeei, the bus. The alignment has a direct effect on the performance of the radio links.

Eye injury may occur, however, if an optical tool such as a microscope, magnifying glass, or eye loupe is used to view an un-terminated optical fiber.

  HARRY POTTER AND THE BELOVED INCUBUS PDF

System network service access A network address defined by ISO, through which entities huaewi the network layer can point access OSI network services. Select the online IF board.

Click Options to change the VC timeslot numbering policy used by the cross- connection. It provides the following functions: All or part of the products, services and features described in this document may not huawdi within the purchase scope or the usage scope.

Click OK again to close the dialog box. Password – – This parameter specifies the password of the gateway NE.

RTN 950 V100R005C01 Commissioning Guide 04

It also supports the channels in the bandwidth mode. Figure Toggle lever switch O: Supports automatic re-login in the case of disconnection. Step 8 Repeat Steps 1 through 7 to check the fiber jumper that is connected to the RX port.

Drilling holes without complying with the requirements affects the electromagnetic shielding performance of the cabinet and damages the cables inside the cabinet.

Otherwise, relog in to the system according to the prompt message of the system. Then, the tributary board configuration interface is displayed. Step 3 Connect the network cable that passes the test to the Ethernet port of the device.

First, reconstruct the power supply and then test the output voltage again.

The curve diagram should be green. Configure the parameters of the new maintenance domains.

Tools, Equipment, and Materials Network cable tester Background Information You can also test the connectivity of a network cable by performing a loopback on the data ports this method is applicable when the equipment is powered on.

  CHARLES WALDHEIM LANDSCAPE URBANISM PDF

Instructions Regarding Fiber Handling Read and abide by the following instructions before handling fibers: If you select IP auto discovery, then: As a result, points 6 and 7 may be mistaken for the peak point of the main lobe signal. The main difference is with regard to the key arrangement.

OptiX RTN – Enterprise Service Support

Step 4 Click New. Prerequisite l The fiber jumper is installed and routed from the optical interface to the ODF. The Confirm dialog box is displayed. Use the same user Selected Deselected When this parameter is selected, enter User name and Deselected Name and Password to log in to all the password to login selected NEs. Provides additional information to emphasize or supplement important points of the main text.

Step 4 Disable the E1 priority function and AM function on the radio link between two sites. If more than 30 nodes exist in the orderwire subnet, it is recommended that you set this parameter to nine seconds. Turn it to the right.

In this case, adjust the azimuth of the antenna to the middle of points 4 and 5 as shown in Figure In normal situation, Working should be Standby, and Protection should be Active. Such static electromagnetic effects can remain for an appreciable time.